Automotive Paint and Supplies
autopaint@paintforcars.com

848-448-8186 Click for the BBB Business Review of this Auto Paint - in Toms River NJ

TCI Urethane Clear Coat - 6050

TCI Urethane Clear Coat - 6050
    Photos are intended for general color reference only. Refer to Color Chart for actual color samples.
     


    TCI 6050 - Technical Information Sheet

    DESCRIPTION: 6050 Universal Clear
    A 4:1 mixing ratio Clear. It provides a high quality finish with excellent gloss, leveling, and flow characteristics. An excellent value without sacrificing quality.

    INSTRUCTIONS:

    Applying Basecoat

    • Apply in accordance with manufacturer’s instructions
    • Permit the basecoat to fully dry prior to applying clear
    • Remove surface contaminants with tack cloth prior to applying clear

    Mixing & Applying Clearcoat

    • Thoroughly mix four parts of 6050 with one part of 601 series hardener
    • Set gun pressures according to Gun Set-up directions
    • Apply one medium coat followed by one full wet coat allowing 3 to 5 minute flash time between coats
    • For best results, an additional full wet coat may be applied following a 5 minute flash time
    • Keep spray gun 6 – 10 inches from surface, adjust speed of travel to apply wet coat with each pass, overlapping approximately 50%
      Note: air may be entrapped if the distance between the gun and surface is too close or gun travel is too slow

    Buffing

    • Force dry – follow Bake directions before wet sanding/buffing.
    • Air dry – for best results cure overnight before wet sanding/buffing.
    • 6050 can be wet sanded in as little as four hours at 75º F
      Note: cure time may vary with film thickness and temperature

    GENERAL:

    Appearance -Clear Liquid
    Viscosity, RTS - 23 – 24 seconds #2 Zahn
    Shelf Life -One Year (unopened)
    RTS VOC -4.2 lb/gal (500 g/L)
    RTS Solids by Weight - 33%
    Pot Life -3 hrs @ 75˚ F
    Product Size
     - Clearcoat - 6050 - Gallon or quart can
     - Activator - 601 Fast - Quart or half pint can
     - Activator - 602 Medium - Quart or half pint can
     - Activator - 603 Slow - Quart or half pint can

    BASECOATS/SUBSTRATES

    6050 Clearcoat is compatible with most high quality basecoats.
    Refer to basecoat manufacturing technical data sheets.
    (If not sure of compatibility, test first in an inconspicuous area)
    Recommended substrate temperature: 70º – 80º F (21º – 27º C)

    GUN SET-UP TIP AIR PRESSURE
    Conventional 1.3 - 1.4 mm 40 - 50 psi (at gun)
    HVLP 1.2 - 1.3 mm 8 - 10 psi (at aircap)

    FLASH & DRY TIMES :
     -
    Flash Time between coats at 75ºF    3 to 5 minutes
     - Dust Free Time at 75ºF                 30 minutes

    GUN CLEAN-UP:
     -
    Clean equipment with a high quality lacquer thinner immediately after spraying

    BAKE:
     - Allow ten minute flash time before force drying
     - Bake for 30 minutes at 140º F
     - Cool for one hour after force drying before wet sanding

    RECOATING:
     -
    Recoat after 12 hours air dry at 75º F
       or
     - Recoat after 2 hours cool down after force drying

    GUN CLEAN-UP:
     -
    Clean equipment with a high quality lacquer thinner immediately after spraying

    ADDITIVES:
    FISH EYE – The use of fish eye eliminator discouraged because it can impact the flow and leveling of the clearcoat  
    ACCELERATOR – The use of additional catalysts is not recommended as it can cause solvent popping and/or loss of gloss

    TECHNICAL INFO: For additional technical information call (800-824-4999)

    SAFETY DATA: Refer to MSDS for 6050, 601, 602, 603

    FOR INDUSTRIAL USE ONLY.

    TO PROTECT AGAINST HARMFUL VAPOR & SPRAY WEAR A POSITIVE - PRESSURE SUPPLIED AIR RESPIRATOR (NIOSH APPROVED), EYEPROTECTION, GLOVES AND PROTECTIVE CLOTHING WHILE MIXING AND SPRAYING. FOLLOW MSDS FOR APPROPRIATE SAFETY AND HEALTH INSTRUCTIONS

    DISCLAIMER: The information contained on this Technical Data Sheet is intended to assist you in product application. It is based on knowledge of general industry use, experience & research. Since conditions of storage, handling, and product use are not under our control, buyers must assume responsibility for suitability of the product for their specific purposes.


     

     


    © 1998-2015 PaintForCars.com

    Always read, understand and follow the product information and instructions provided. Product use is void where prohibited,
    and is intended for use only by professionals or under a professional's supervision. PaintForCars.com and Trinity 1945 Inc. are
    not responsible for adverse results while using our products. Liability, if any, shall not exceed a refund of the purchase price.