Celebrating 21 Years of Automotive Paint & Supplies

Mini Cart

Sold Out

TCI Premium 2K Urethane Primer Surfacer w/Activator

$102.53

Out of stock

Description

TCI 2K High Build Urethane Primer Surfacer
4200 | Gray – 4.4 VOC (1 Gallon/3.785 Liters)
Included with purchase
422 | TCI Activator – 4.4 VOC

PRODUCT DESCRIPTION:
TCI Premium Gray 2K High Build Urethane Primer is formulated for maximum holdout and minimal sand-scratch swelling. Dries fast and builds quickly.

TECHNICAL DATA:
Color: Gray
Mixing Ratio: 4:1:1
Catalyst: #422 Activator
1.5mm – 2.2mmm for Conventional and HVLP guns
35-45 psi at the gun for Conventional gun
28-35 psi at the gun for HVLP gun
Film Build : 3.0 mils wet
Pot Life: 3 hours
VOC: 4.4 lbs/gallon (RTS)


TCI 4200- Technical Information Sheet

DESCRIPTION: 4200 Premium 2K Urethane Primer 
4200 is a two component acrylic urethane primer designed to provide ease of sanding as well as exceptional adhesion, film build, and cure time.

INSTRUCTIONS:

  • Sand original finish with medium grit sandpaper
  • Clean all area with wax and grease remover
  • Surface should be clean and dry before applying product
  • Spray two or three medium coats of 4200, allowing each coat to flash to a dull appearance before applying the next coat.
  • For best results force dry or allow to air dry for one hour before sanding
  • 4200 can be block or machine sanded with P320 or P400, or wet sanded with P400 or P500 grit before applying topcoat

GENERAL:

Appearance -Gray Liquid
Viscosity -Full Bodied
Shelf Life -One Year (unopened)
VOC -3.74 lb/gal (448 g/L)
Pot Life -30 – 60 Minutes @ 75˚ F
Product size
– 
Primer – 4200 -One gallon or quart cans
 – Activator – 422 – Cone top quart or half pint cans

PRODUCT MIXING:

  • Thoroughly mix four parts 4200 with one part of 422 activator
  • May be reduced 4:1:1 with urethane reducer if a lower viscosity is desired

SUBSTRATES:

  •  Coat large bare metal, steel & aluminum areas with proper self-etching sealer
  •  Recommended substrate temperatures: 50˚ F – 100˚ F.
GUN SET-UPTIPAIR PRESSURE
Siphon Feed1.8 – 2.0 mm30 – 40 psi
Gravity Feed1.6 – 2.0 mm25 – 40 psi
HVLP (gravity)1.6 – 2.0 mm6 – 10 psi


GUN CLEAN-UP: 
Clean equipment with a high quality lacquer thinner immediately after spraying

TECHNICAL INFO: For additional technical information call (800-824-4999)

SAFETY DATA: Refer to SDS for 4200 and 422

FOR INDUSTRIAL USE ONLY.

TO PROTECT AGAINST HARMFUL VAPOR & SPRAY WEAR A POSITIVE – PRESSURE SUPPLIED AIR RESPIRATOR (NIOSH APPROVED), EYEPROTECTION, GLOVES AND PROTECTIVE CLOTHING WHILE MIXING AND SPRAYING. FOLLOW SDS FOR APPROPRIATE SAFETY AND HEALTH INSTRUCTIONS

DISCLAIMER: The information contained on this Technical Data Sheet is intended to assist you in product application. It is based on knowledge of general industry use, experience & research. Since conditions of storage, handling, and product use are not under our control,buyers must assume responsibility for suitability of the product for their specific purposes.

Additional information

Weight12 lbs
Dimensions6.5 × 6.5 × 9 in

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.

Out of stock