Celebrating 21 Years of Automotive Paint & Supplies

Mini Cart

Sold Out

TCI Premium 2K Urethane Primer Surfacer w/Activator

$74.00

Out of stock

Description

TCI 2K High Build Urethane Primer Surfacer
4200 | Gray – 4.4 VOC (1 Gallon/3.785 Liters)
Included with purchase
422 | TCI Activator – 4.4 VOC

PRODUCT DESCRIPTION:
TCI Premium Gray 2K High Build Urethane Primer is formulated for maximum holdout and minimal sand-scratch swelling. Dries fast and builds quickly.

TECHNICAL DATA:
Color: Gray
Mixing Ratio: 4:1:1
Catalyst: #422 Activator
1.5mm – 2.2mmm for Conventional and HVLP guns
35-45 psi at the gun for Conventional gun
28-35 psi at the gun for HVLP gun
Film Build : 3.0 mils wet
Pot Life: 3 hours
VOC: 4.4 lbs/gallon (RTS)


TCI 4200- Technical Information Sheet

DESCRIPTION: 4200 Premium 2K Urethane Primer 
4200 is a two component acrylic urethane primer designed to provide ease of sanding as well as exceptional adhesion, film build, and cure time.

INSTRUCTIONS:

  • Sand original finish with medium grit sandpaper
  • Clean all area with wax and grease remover
  • Surface should be clean and dry before applying product
  • Spray two or three medium coats of 4200, allowing each coat to flash to a dull appearance before applying the next coat.
  • For best results force dry or allow to air dry for one hour before sanding
  • 4200 can be block or machine sanded with P320 or P400, or wet sanded with P400 or P500 grit before applying topcoat

GENERAL:

Appearance -Gray Liquid
Viscosity -Full Bodied
Shelf Life -One Year (unopened)
VOC -3.74 lb/gal (448 g/L)
Pot Life -30 – 60 Minutes @ 75˚ F
Product size
– 
Primer – 4200 -One gallon or quart cans
 – Activator – 422 – Cone top quart or half pint cans

PRODUCT MIXING:

  • Thoroughly mix four parts 4200 with one part of 422 activator
  • May be reduced 4:1:1 with urethane reducer if a lower viscosity is desired

SUBSTRATES:

  •  Coat large bare metal, steel & aluminum areas with proper self-etching sealer
  •  Recommended substrate temperatures: 50˚ F – 100˚ F.
GUN SET-UPTIPAIR PRESSURE
Siphon Feed1.8 – 2.0 mm30 – 40 psi
Gravity Feed1.6 – 2.0 mm25 – 40 psi
HVLP (gravity)1.6 – 2.0 mm6 – 10 psi


GUN CLEAN-UP: 
Clean equipment with a high quality lacquer thinner immediately after spraying

TECHNICAL INFO: For additional technical information call (800-824-4999)

SAFETY DATA: Refer to SDS for 4200 and 422

FOR INDUSTRIAL USE ONLY.

TO PROTECT AGAINST HARMFUL VAPOR & SPRAY WEAR A POSITIVE – PRESSURE SUPPLIED AIR RESPIRATOR (NIOSH APPROVED), EYEPROTECTION, GLOVES AND PROTECTIVE CLOTHING WHILE MIXING AND SPRAYING. FOLLOW SDS FOR APPROPRIATE SAFETY AND HEALTH INSTRUCTIONS

DISCLAIMER: The information contained on this Technical Data Sheet is intended to assist you in product application. It is based on knowledge of general industry use, experience & research. Since conditions of storage, handling, and product use are not under our control,buyers must assume responsibility for suitability of the product for their specific purposes.

Reviews

There are no reviews yet.

Be the first to review “TCI Premium 2K Urethane Primer Surfacer w/Activator”

Out of stock

***Always read, understand, and follow the product information and instructions provided. Product use is void where prohibited, and is intended for use only by professionals or under a professional's supervision. PaintForCars.com and Trinity 1945 Inc. are not responsible for adverse results while using our products. Liability, if any, shall not exceed a refund of the purchase price.