5414 | D.T.M. Self-Etch Filler Primer (1 Gallon/3.785 Liters)
5415 | D.T.M. Self-Etch Filler Activator (1 Gallon/3.785 Liters)
5 STAR XTREME #5414 Self-Etching Primer is a Chromate Free Metal Etching Filler that is ideal for spot/panel repairs where bare metal is present. It increases both adhesion and corrosion protection on bare substrates. It fills minor surface imperfections and may be topcoated directly for quick and easy repairs.
Self-Etching Primer Filler for use on steel, fiberglass, aluminum and certain galvanized and zinc coated steel. Can be topcoated directly.
5 STAR AUTOBODY PRODUCTS
TECHNICAL DATA INFORMATION
DATED: MAY 2013
PRODUCT NUMBER – DESCRIPTION
#5414 – D.T.M Etch Primer (Gallon) – NATIONAL RULE
#5415 – D.T.M Etch Primer Reducer (Gallon) – NATIONAL RULE
5414 Etch Primer and 5415 Etch Reducer is a Chromate Free Metal Etching Primer that is ideal for spot/panel repairs where bare metal is present. It increases both adhesion and corrosion protection on bare substrates. It fills minor surface imperfections and may be topcoated directly for quick and easy repairs.
Steel, Fiberglass, Galvanized Steel, Cured Body Filler, Aluminum, OEM Enamels, OEM Lacquers.
Volume Solids_______________________11% (Mixed)
Film Build Full Wet Coats_______________1 mil
Flash Point__________________________48 Degrees F
Pot Life_____________________________24 Hours
Theoretical Coverage__________________176 sq. ft.
MIXING: NATIONAL RULE _______1 PART 5414: 1 PART 5415
MIXING: LOW VOC _____________1 PART 5414: 1 PART 5415: 2 PARTS 5910 ACETONE
Mix the components in the order and ratio indicated above. Stir thoroughly after adding each item.
Clean all areas to be painted with 5 STAR XTREME #5900 Wax & Grease Remover to remove all dirt, wax, grease and other contaminants. Surface must be clean and dry. Grind repair area to remove paint and all rust as needed. Apply #5064 5 STAR XTREME Premium Body Filler, if required. Sand all areas to be refinished and featheredge all broken film areas with 320 grit. Use 36” masking paper to prevent overspray problems.
Spray at 5-9 PSI at the cap for HVLP or 30-35 PSI for conventional guns. Apply 2-3 medium wet coats allowing 2-3 minutes flash time between coats.
Recoat in 30 minutes, sand in 60 minutes, after 24 hours must be lightly scuffed before topcoating. Final dry film thickness should be a minimum of 1.0 mil.
Clean spray equipment immediately after use with Urethane Grade Reducer or 5 STAR XTREME #5414 Virgin Wash Thinner. Do not leave material in spray gun.
In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention. For skin: Wash thoroughly with water. If difficulty in breathing is experienced, get medical attention immediately. If swallowed, do not induce vomiting, get medical attention immediately. See Material Safety Data Sheet.
SAFETY INFORMATION – FOR INDUSTRY USE ONLY
Danger: Vapor harmful. May affect the brain or nervous system causing dizziness, headache, or nausea. May cause eye, skin, nose, and throat irritation. Harmful if swallowed. Precautions: Vapors may ignite explosively. Keep away from heat, sparks, and flame. Vapors may cause flash fire. Do not smoke. Extinguish all flames and pilot lights, and turn of stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapor or spray mist. Do not get in eyes, on skin or clothing. Wash thoroughly after handling. Wear solvent resistant gloves. The material id designed for application only by professionally trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public.
KEEP OUT OF REACH OF CHILDREN.
Only logged in customers who have purchased this product may leave a review.