Automotive Paint and Supplies
848-448-8186
autopaint@paintforcars.com

MAXX FILL 2K High Build Urethane Primer Surfacer w/ Activator

MAXX FILL 2K High Build Urethane Primer Surfacer w/ Activator
    Photos are intended for general color reference only. Refer to Color Chart for actual color samples.
     


    5451 is formulated to provide a fast-drying, high-build film that has maximum adhesion, easy sanding properties and excellent color holdout. 5451 is designed to be used on
    properly prepared steel, aluminum, iron, fiberglass and previously painted surfaces. This primer surfacer can be topcoated with any paint system.Offered in a Gray color.
     

    PRODUCT DESCRIPTION:
    5451 is formulated to provide a fast-drying, high-build film that has maximum adhesion, easy sanding properties and excellent color holdout. 5451 is designed to be used on properly prepared steel, aluminum, iron, fiberglass and previously painted surfaces.This primer surfacer can be topcoated with any paint system.Offered in a Gray color.

    FEATURES:
      • 4.4 VOC
      • 4:1:1 Mix Ratio
      • Tintable
      • Excellent Adhesion Characteristics
      • Hi-Build, Superior Holdout
      • Fast Drying
      • Easy Sanding Properties
      • Can Be Topcoated With Any Automotive Paint System

    PRODUCTS:

     

    Gallon

    Quart

    Half Pint

    4.4 VOC Primer (Gray)

    #5451-1

    #5451-4

     

    4.4 VOC Activator

     

    #5457-4

    #5457-16

    SURFACE PREPARATION:
    Clean all areas to be painted with 5 STAR #5900 Wax & Grease Remover to remove all dirt,wax, grease and other contaminants. Featheredge and sand original finish. Surface must be clean and dry. Bare metal, galvanized steel, and aluminum should be coated with 5 STAR #5414 & #5415 Self Etching Primer prior to applying #5451 MAXX FILL 2K High Build Primer.

    MIXING DIRECTIONS:

    Mix the components in the order and ratio indicated below. Stir thoroughly after adding each item.

     

    Hide Build Mixture

     




    4 PARTS #5451 MAXX FILL Gray Primer
    Mixing or Tinting Base (Not Required)
    1 PART 5 STAR Urethane Grade Reducer
    1 Part#5457 MAXX FILL Activator

     

    Extra High Build Mixture



    4 PARTS #5451 MAXX FILL Gray Primer
    Mixing or Tinting Base (Not Required)
    1 Part#5457 MAXX FILL Activator

     

    Tinting Mixture



    4 PARTS #5451 MAXX FILL Gray Primer
    1/2 PART Mixing or Tinting Base
    1 PART 5 STAR Urethane Grade Reducer
    1 Part#5457 MAXX FILL Activator

    APPLICATION DIRECTIONS:
    Apply 2 full wet coats at 40-50 psi to achieve 3 mils of film that can be sanded and topcoated in 3 hours. Sanding and cure time may be longer depending on thickness of application, tints used and/or temperature. Let each coat flash 5-10 minutes.
    Better appearance and holdout will be achieved by letting dry overnight prior to sanding and topcoating. It can also be force-dried for 30 minutes at 140°F (60°C) after allowing the final coat to flash 20 minutes. Films in excess of 3 mils should not
    be force-dried. #5451 should always be sanded before topcoating.

    POT LIFE:
    Pot life of activated primer is approximately 3 hours. Some mixing bases may shorten the pot life.Test your system before proceeding.

    COMPATIBLE BASECOATS :
    BASF,Dupont, ICI, PPG, Sherwin Williams, Sikkens, Spies Hecker,Valspar.

    GUN SETUP: 

    1.5mm - 2.2mmm for Conventional and HVLP guns   

    35-45 psi at the gun for Conventional gun 

    28-35 psi at the gun for HVLP gun 

     
    CLEAN UP:
    Clean spray equipment immediately after use with Urethane Grade Reducer or 5 STAR #5214 Virgin Wash Thinner. Do not leave material in spray gun.

    FIRST AID:
    In case of eye contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention. For skin: Wash thoroughly with water. If difficulty in breathing is experienced, get medical attention immediately. If swallowed, do not induce vomiting, get medical attention immediately. See Material Safety Data Sheet.

    SAFETY INFORMATION – FOR INDUSTRY USE ONLY:
    Danger: Vapor harmful.May affect the brain or nervous system causing dizziness, headache, or nausea.May cause eye, skin, nose, and throat irritation. Harmful if swallowed. Precautions: Vapors may ignite explosively. Keep away from heat, sparks, and flame.Vapors may cause flash fire.Do not smoke. Extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors and other sources of ignition during use and until all vapors are gone. Prevent buildup of vapors by opening all windows and doors to achieve cross-ventilation. Use only with adequate ventilation. Do not breathe vapor or spray mist.Do not get in eyes, on skin or clothing.Wash thoroughly after handling.Wear solvent resistant gloves.The material id designed for application only by professionally trained personnel using proper equipment under controlled conditions, and is not intended for sale to the general public. KEEP OUT OF REACH OF CHILDREN.

     

    Best Price Online

    $65.00
    Selecet Size:
    Select Color:

    Shipping/Return Policy
    Contact Us

    "PaintForCars ships quick and delivers what they advertise."
    - Steedjohnd from eBay
    Flammable products can only ship by ground, and
    only within the Continental US. International,
    AK, HI, Next Day and 2nd Day, delivery are not available.

    Related Products

     
    Starfire Automotive Finishes Color Chip Chart
    Paintforcars Starfire Acrylic Urethane Reducer medium speed 1 quart
    MAXX SOLV Wax & Grease Remover
    5 Star MaxFill 2K Activator - 5457
    Flow Star Urethane Reducers
    Gerson Blue Resperator
    5 Star X-treme Hand Cleaner


     


    © 1998-2013 PaintForCars.com