Automotive Paint and Supplies
848-448-8186
autopaint@paintforcars.com

5 Star Xtreme Charcoal Mist Metallic Urethane Paint Kit - 8008

5 Star Xtreme Charcoal Mist Metallic Urethane Paint Kit - 8008
    Photos are intended for general color reference only. Refer to Color Chart for actual color samples.
     


    5 STAR XTREME AUTOBODY PRODUCTS

    TECHNICAL DATA INFORMATION

    DATED: AUGUST 2012_REVISED

    PRODUCT DESCRIPTION:

    5 STAR XTREME #8000 Series 2.8 VOC Acrylic Urethane Colors are high solids, high gloss, low VOC coatings intended for use as a protective maintenance coating for automotive and industrial applications, surfaces exposed to humidity, chemicals and corrosive elements.

    PLEASE SHAKE AND STIR ALL PRODUCTS THOROUGHLY

    #8000 SERIES CUSTOM COLOR/CATALYST:

    HIGH PERFORMANCE URETHANE SINGLE STAGE SERIES 2.8 VOC - GALLON

    #8000-01 Gloss Black

    #8001-01 Hot Rod Black

    #8002-01 Brilliant Black Pearl

    #8003-01 Gloss White

    #8004-01 Fleet White

    #8005-01 Pure White

    #8007-01 Oxford White

    #8008-01 Charcoal Mist Metallic

    #8009-01 Galaxy Silver

    #8010-01 Viper Red

    #8011-01 Swift Red

    #8012-01 Candy Apple Red

    #8013-01 International Harvester Red

    #8014-01 Allis Chalmers Orange

    #8015-01 New Cat Yellow

    #8016-01 School Bus Yellow

    #8017-01 John Deere Yellow

    #8018-01 John Deere Green

    #8019-01 Ford Blue

    HIGH PERFORMANCE URETHANE SINGLE STAGE SERIES 2.8 VOC -QUART

    #8030-04 Premium Low VOC Reducer

    #8040-04 2.8 VOC High Performance Urethane Paint Catalyst

    DIRECT TO METAL ADHESION

    NOTE: Performance is better when using DTM Primer under #8000 series paint.

    POT LIFE

    Pot life will be about 3-5 hours at 77° F.

    MIXING DIRECTIONS (4:1:1):

    2.8 VOC

    4 PARTS #8000 Series Single Stage

    1 PART #8040 Catalyst

    1 PART #8030 Reducer or quality grade Low VOC urethane reducer

    SURFACE PREPARATION:

    1. Wash area thoroughly with soap and water to remove contaminates that solvent based cleaners cannot remove effectively. 2. Clean area with Wax and Grease Remover. 3. Use a tack cloth to remove any surface contaminants that may have settled on the repaired areas prior to paint application. 4. Apply #8000 series High Performance Urethane Single Stage Color.

    APPLICATION DIRECTIONS:

    Adjust air pressure to 40-50 psi at gun for gravity, siphon feed guns or HVLP use 6-10 psi at air cap. Apply 2-3 medium coats (maximum 2 mils wet per coat) or until hiding is achieved. Allow a 15-20 minute flash time between coats and before force drying.

    DRY TIMES AT 77°F:

    FLASH TIME 15-20 MINUTES

    TO DELIVER 16-24 HOURS

    FORCE DRYING AT 140°F:

    PURGE TIME 15 MINUTES

    BAKE TIME AT 140°F 40 MINUTES

    RECOATING:

    2.8 VOC XTREME #8000 Urethane Single Stage Color may be recoated after 16-24 hours at 77° F. After 16-24 hours it must be lightly sanded/scuffed before additional color or clearcoat may be applied.

    ACCELERATOR & FISHEYE ELIMINATOR:

    Accelerator and/or Fisheye Eliminator is not recommended for use in this product.

    CLEAN-UP:

    Clean spray equipment immediately after use with 5 STAR XTREME Gun Wash, or a high quality lacquer thinner, or compliant solvent depending on area regulations.

    TECHNICAL DATA:

    Color: Various

    Catalyst: #8040

    Low VOC Reducer: #8030

    Mixing Ratio (2.8 VOC): 4:1:1

    Weight Solids (RTS): 52 - 70%

    Viscosity #2 Zahn (RTS): ____________________ 18 - 28 seconds #2 Zahn

    Pot Life: 3-5 hours

    Film Build per coat: _________________________ 1.0-2.0 mils per full wet coat

    Coverage: 850 sq.ft. per gallon @ 1 dry mil

    Disposal/Safety: ____________________________ See MSDS for this product

     
     


    © 1998-2013 PaintForCars.com